Seite 1

70" MAX

ISSUED: JUNE 2014

Caution: DO NOT EXCEED RATED LISTED WEIGHT. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!

INSTALLATION MANUAL

LED Wall Mount

Seite 2

ST6.3x55 (x3), W-A concrete anchor W-B (x3)
Package M, Package W
adaptor bracket A (x1)
small supporting spacer (x2) C
big supporting spacer (x2) D
wall plate B (x1)

Note: Read the entire instruction manual before you start installation and assembly. Component Checklist

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, telephone your local distributor for a replacement.

• Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instructions or warnings, please contact your local distributor.
• This mounting bracket was designed to be installed and utilised ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury.
• This product should only be installed by someone with good mechanical ability who has basic building experience and fully understands this manual.
• Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. The use of a stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can cause damage to the items, This greatly reduces their holding power.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

Seite 3

With the arrow pointing up. Drill pilot holes

1. Drill pilot holes 60mm (2.4") 60mm (2.4")
2. Mark the exact location of mounting holes

ø 10mm (ø 3/8")

WARNING

• Make sure that mounting screws are anchored into the center of the studs. The use of a stud finder is highly recommended.
• Installers are responsible to provide hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.

1. Removing the Decorative Cover

Remove the plastic cover by releasing these two clasps. Separate the decorative cover from the wall plate by pulling the decorative cover upward.

2a. For Wood Stud Wall Mounting

2b. For Solid Brick and Concrete Mounting

W-A. Make sure the triangle is pointing to the steel ball.

1. Drill pilot holes ø 4.5mm (ø 3/16") 55mm (2.2") 55mm (2.2")
2. Find and mark the exact location of mounting holes
3. Screw the wall plate onto the wall

Make sure the triangle is pointing to the steel ball. With the arrow pointing up.

Seite 4

4. Installing the Adapter Bracket and Spacers

3. Installing the Decorative Cover

Caution: Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.

W-B, W-A. Make sure the triangle is pointing to the steel ball. Screw the wall plate onto the wall.

C 19mm M-C M-G M-H M-C M-D M-E M-G M-H M-H M-D M-E M-G M-I M-D M-E M-G M-I M-H or or or M-C M-G M-H M-C M-D M-E M-G M-H M-H or M-D M-E M-G M-I M-D M-E M-G M-I M-H or M-A M-B M-C C M-F M-G M-A M-B M-C M-F M-G TVTV TVTV or

4.1

Seite 5

4.2

After the wall plate has been safely secured to the wall, carefully lift your TV and hook the top adapter bracket to the wall plate rail. 38mm

5. Hanging the TV onto the Wall Plate

Tighten all screws but do not over tighten.
· Position the adapter brackets as close as possible to the center of the TV.
· Screw the adapter brackets onto the TV.
Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screen.

M-D M-E M-G M-H C D M-D M-E M-G M-H M-D M-E M-G C D M-G M-D M-E TVTV TVTV

Seite 6

5 Removing Flat Panel Screen

You have to lift up screen until the screen can't be lifted.

6. Removing the TV

Put it down back slowly in order to unlock the bracket.

The second time when you lift up, you can remove it from wall plate. 20mm

Maintenance

• Check that the bracket is secure and safe to use at regular intervals (at least every three months).
• Please contact your distributor if you have any questions.

Legal & Compliance

Product identification

Model: PM-SLIMFIX-65 – manual version 1.0

Warranty and liability

The manufacturer grants the full statutory warranty on all new devices. As the manufacturer has no influence on installation, the warranty only applies to the product itself. If you detect a fault or damage, please contact your dealer and provide your sales slip or invoice as proof of purchase.

The manufacturer is not liable for damage to persons or property caused by improper installation, operation or maintenance not described in this manual. Do not alter or modify the product or its accessories. Any use other than described in this manual is not permitted and voids warranty and guarantee.

Trademarks and disclaimer

Product model and logo are trademarks. All other company and product names mentioned are trademarks of their respective owners. All rights reserved. No part of this publication may be copied or reproduced without prior written permission. We reserve the right to make changes to the device, packaging or manual and accept no liability for misprints.

Packaging

Dispose of packaging separately by material (paper/cardboard, plastics) via the local collection systems. Keep packaging material away from children – risk of suffocation. Packaging register LUCID: DE5958616449295.