Component Checklist

Note: Read the entire instruction manual before you start installation and assembly.

• Package W
• concrete anchor
• W-B (x3) ST5.5x50
• W-A (x3) D6 washer (x3)
• W-C
• Package M
• D8 (x4)
• M-F washerD (x4)
• M-E 5 washer small spacer (x8)
• M-G M5x14
• M-B (x4) M6x14
• M-C (x4) M8x20
• M-D (x4) M4x14
• M-A (x4)
• Allen key (x2)
• C wire saddle
• B (x2)
• wall mount (x1)
• A

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, telephone your local distributor for a replacement.

• Do not begin the installation until you have read and understood the instructions and warnings contained in this installation sheet. If you have any question regarding any of the instructions or warnings, please contact your local distributor.
• This mounting bracket was designed to be installed and utilised ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury.
• This product should only be installed by someone with good mechanical ability who has basic building experience and fully understands this manual.
• Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. The use of a stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can cause damage to the items, This greatly reduces their holding power.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

X X√

1. Screw the wall mount onto the wall
2. Drill pilot holes

1. Mark the exact location of mounting holes ø 8mm (ø 5/16" )
2. Drill pilot holes

1. Screw the wall mount onto the wall

1. Find and mark the exact location of mounting holes ø 4mm (ø 5/32") 55mm (2.2") 50mm (2") 55mm 2.2”( ) 55mm (2.2”)

• W-A
• W-C
• W-A
• W-C W-B

X

1. Installing the Wire Saddles

2a. Wood Stud Wall Mounting

2b. Solid Brick and Concrete Mounting

Caution: Make sure that mounting screws are anchored into the center of the studs. The use of a stud finder is highly recommended.

Caution: Installers are responsible to provide hardware for other types of mounting situations.

Caution: Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.

4. Cable Management2. Install VESA Plate3 Attach the TV to the VESA Plate.

Connect cables to your TV and route through the wire saddles.
Note: Leave slack in cable for cantilever arm movement. Tighten all screws but do not over tighten.
Lift the TV and match the holes on your TV with the holes on the mount. Secure your TV to the mount by tightening screws.

• M-E
• M-F
• M-A
• M-B
• M-C
• M-D
• M-G
• M-G M-F
• M-D
• M-G M-F
• M-D

Legal & Compliance

Product identification

Model: PM-BASIC2-37 – manual version 1.0

Warranty and liability

The manufacturer grants the full statutory warranty on all new devices. As the manufacturer has no influence on installation, the warranty only applies to the product itself. If you detect a fault or damage, please contact your dealer and provide your sales slip or invoice as proof of purchase.

The manufacturer is not liable for damage to persons or property caused by improper installation, operation or maintenance not described in this manual. Do not alter or modify the product or its accessories. Any use other than described in this manual is not permitted and voids warranty and guarantee.

Trademarks and disclaimer

Product model and logo are trademarks. All other company and product names mentioned are trademarks of their respective owners. All rights reserved. No part of this publication may be copied or reproduced without prior written permission. We reserve the right to make changes to the device, packaging or manual and accept no liability for misprints.

Packaging

Dispose of packaging separately by material (paper/cardboard, plastics) via the local collection systems. Keep packaging material away from children – risk of suffocation. Packaging register LUCID: DE5958616449295.