← Products
PureMounts® TV-Wandhalterung - Move 32-55''
Discontinued

PM-MOVE-52A

PureMounts® TV-Wandhalterung - Move 32-55''

PureMounts® TV Wall Mount - Move 32-55''.

ManualFAQ
PDF / print
Chapter 1 of 7

Seite 1

SLIM FULL MOTION LED/LCD TV WALL MOUNT

INSTALLATION INSTRUCTIONS

PM-MOVE-52A

47" MAX
100x100/200x100
200x200/400x200
300x300/400x400

2.5~20kg
(5.5~44lbs)

ISSUED: OCT. 2012

Caution: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!

Maintenance

  • Check that the bracket is secure and safe to use at regular intervals (at least every three months).
  • Please contact your dealer if you have any questions.
Chapter 2 of 7

Seite 2

Note: Read the entire instruction manual before you start installation and assembly.

WARNING

Component Checklist

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installing. If any parts are missing or faulty, telephone your local distributor for a replacement.

  • Do not begin the installation until you have read and understood the instructions and warnings contained in this installation sheet. If you have any question regarding any of the instruction or warning, please contact your local distributor.
  • This mounting bracket was designed to be installed and utilized ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury.
  • This product should only be installed by someone of good mechanical ability, with basic building experience and fully understanding of this manual.
  • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
  • If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. The use of a stud finder is highly recommended.
  • Always use assistant or mechanical lifting equipment to safely lift and position equipment.
  • Tighten screws firmly, but do not over tighten. Over tightening can damage the items, greatly reducing their holding power.
  • This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

Package W

  • ST6.3x55 (x3)
  • W-A concrete anchor (x3)

Package M

  • M5x14 M-A (x4)
  • M6x14 M-B (x4)
  • M8x20 M-C (x4)
  • M6x30 M-D (x4)
  • M8x30 M-E (x4)
  • big spacer M-I (x4)
  • small spacer M-H (x8)
  • washer D (x4) M-F
  • washer D8 (x4) M-G
  • 3mm (x1) E
  • Allen key 6mm (x1) F
  • Allen key
  • articulated arm assembly A
  • VESA adaptor (x ) C
  • 2 VESA adaptor (x ) D
  • 2 M6 B (x8)
Chapter 3 of 7

Seite 3

1. Separate VESA Plate from Wall Mount

  1. Remove the lower flat nut.
  2. Loosen the upper nut, Remove VESA plate.

WARNING

  • Make sure that mounting screws are anchored into the center of the studs. The use of a stud finder is highly recommended.
  • Installers are responsible to provide hardware for other types of mounting situations.
  • Installers must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

3a. Mount on Wood Stud Wall

  1. Find and mark the exact location of mounting holes.
  2. Drill pilot holes
  3. Screw the wall mount onto the wall

2. Remove the Decorative Covers

  • W-A ø 4.5mm (ø 3/16") 55mm (2.2") 55mm (2.2")

X X√

Chapter 4 of 7

Seite 4

5. Assemble VESA Adaptors

5a VESA 300x300, 400X400 Unit: mm

300 400
300 400 B

5b VESA 400x200 Unit: mm

400
200

4. Install Decorative Covers

X X√

Caution: When installing wall mounts on cinder block, verify the actual concrete thickness is at least 1-3/8" (35mm) for using the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" (25mm) minimum from the side of the block. It is suggested electric drill on slow setting be used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
Installers must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

WARNING

3b. Mount on Solid Brick and Concrete Block

  1. Mark the exact location of mounting holes
  2. Drill pilot holes
  3. Screw the wall mount onto the wall
  • W-B W-A 60mm (2.4") 60mm (2.4") ø 10mm (ø 3/8")
Chapter 5 of 7

Seite 5

7. Hook the TV onto the Wall Mount

Loosen the upper flat nut spacing 4mm to VESA plate.

4mm

Hook the TV onto the wall mount
· Level the TV.
· Place the lower flat nut and tighten both nuts.

TV TVTV

6. Install VESA Plate

6-1 For Flat Back Screen

TVTV TV

6-2 For Recessed Back Screen

M-A/M-B/M-C M-F/M-G

Note: Choose appropriate screws, washers and spacers (if necessary) according to the type of screen.

  • Position the adapter brackets as close as possible to the center of the display.
  • Screw the adapter brackets onto the display.
  • Tighten all screws but do not over tighten.

M-C M-G M-H M-H M-H M-C M-D M-E M-G M-I M-D M-E M-G M-D M-E M-G M-I M-H or or or

Chapter 6 of 7

Seite 6

8. Tension Adjust

9. Cable Management

Adjust to the desired location or tilt.

10. Adjustment

Tighten screw till the display angle can be fixed.

Connect the cables to the display, and press cable cover inward to route the cables through the space.
Note: Leave slack in cable for cantilever arm movement.

180° 180°
height adjustable
max335mm

+15°

+3° -3°

Note: Please keep the arm level during tension adjustment. Use a proper Allen key to slightly loosen or tighten the adjustment screw according to the display weight.
If display settles on its own, rotate adjustment screw towards the "+" symbol.
If display rises on its own, rotate adjustment screw towards the "-" symbol.

Note: Please tighten socket set screw if the joints make popping sounds in use.

Was this helpful?
← PreviousNext chapter →
Staff sign-in