Safety precautions

Note: To ensure the best from the product, please read all instructions carefully before using the device. Save this manual for further reference.

• Unpack the equipment carefully and save the original box and packing material for possible future shipment.
• Follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
• Do not dismantle the housing or modify the module. It may result in electrical shock or burn.
• Using supplies or parts not meeting the products’ specifications may cause damage, deterioration or malfunction.
• Refer all servicing to qualified service personnel.
• To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
• Do not put any heavy items on the extension cable in case of extrusion.
• Do not remove the housing of the device as opening or removing housing may expose you to dangerous voltage or other hazards.
• Install the device in a place with fine ventilation to avoid damage caused by overheat.
• Keep the module away from liquids.
• Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on to the housing, unplug the module immediately.
• Do not twist or pull by force ends of the optical cable. It can cause malfunction.
• Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
• Unplug the power cord when left unused for a long period of time.
• Information on disposal for scrapped devices: do not burn or mix with general household waste, please treat them as normal electrical wastes.

Product Introduction

The PT-HDBT-701-TXWP is 2x1 wallplate HDBaseT Transmitter for switching and extending HDMI or VGA + audio input to display or projector, and the transmission distance is up to 40m@4K and 70m@1080p over a single Cat5e/6/7 cable based on Certified HDBaseT technology. The resolution of HDMI input is up to 4K/UHD@ 60Hz 4:2:0 and VGA input up to 1920x1200.

The PT-HDBT-701-TXWP is ideal for huddle rooms, classrooms and small conference rooms. The wall‑mountable design provides the convenience of placing input connections precisely where they are needed.

Feature

• Features one HDMI input and one VGA input with 3.5mm analogue audio input.
• Supports HDMI signal up to 4K@60Hz 4:2:0, VGA input signal up to 1920 x 1200.
• Built-in scaling function to match signals to display native resolution.
• Ensures display of content-protected media and interoperability with other HDCP compliant devices.
• Audio signal can be selectively embedded into the video output.
• HDBaseT technology extend HDMI and VGA, Audio, control signals up to 70m over CATx cable.
• Automatically detect active inputs when sources are connected.
• Flexible control options for compatibility with third-party system, matrix switcher or receiver.
• Supports bi-directional RS232 pass-through with HDBaseT connection and local control.
• PoH (power over HDBaseT) allows powering from the receiver at the display end.
• Provides power supply for devices like Control Panel.

Package List

• 1 x PT-HDBT-701-TXWP 4K Wallplate HDBaseT Transmitter
• 1 x 2-pin Pluggable Terminal Block
• 1 x 4-pin Pluggable Terminal Block
• 1 x User Manual

Note: Please confirm if the product and the accessories are all included, if not, please contact with the dealers.

Front Panel

VGA IN AUDIO IN HDMI IN SOURCE/AUTO LINK VGA HDMI IR RESET # 3 # 65 7 # 4 # 1 # 2

Rear Panel

Tx Rx12V 12V RS232IN OUT PoH IN HDBT OUT # 3 4 # 1 # 2

Side Panel

FIRMWARE # 1

Usage Precautions

• Verify all components and accessories included before installation.
• System should be installed in a clean environment, preferably at ambient temperature or within given working temperature range (see page18 for limits).
• All of the power switches, plugs, sockets and power cords should be insulated and safe.
• All devices should be connected before power on.

Overview: Installation

1. If installing in a back-box, it is recommended that the PT-HDBT-701-TXWP be installed in a suitable square box. The square box has sufficient space to terminate the cables with jacks behind the unit when fully installed.
2. Run one Cat5e/6/7 cable from the PT-HDBT-701-TXWP location to the location

VGA IN AUDIO IN HDMI IN SOURCE/AUTO LINK VGA HDMI IR IN RESET Tx Rx12V 12V RS232IN OUT PoH IN HDBT OUT OUTPUTS 13~16 AUDIO MIC IN AUDIO OUT RL MIX OUT RL OUTPUT 4K Tx Rx R L IR OUT IR IN RS232 AUDIO HDBaseT OUTPUT 4K Tx Rx R L IR OUT IR IN RS232 AUDIO HDBaseT OUTPUT 4K Tx Rx R L IR OUT IR IN RS232 AUDIO HDBaseT OUTPUT 4K Tx Rx R L IR OUT IR IN RS232 AUDIO HDBaseT OUTPUT HDMI AUDIO L R 4K OUTPUT HDMI AUDIO L R 4K OUTPUT HDMI AUDIO L R 4K OUTPUT HDMI AUDIO L R 4K 4K RS232 AUDIO Tx Rx R L INPUT IR OUT IR IN HDBaseT 4K RS232 AUDIO Tx Rx R L INPUT IR OUT IR IN HDBaseT 4K RS232 AUDIO Tx Rx R L INPUT IR OUT IR IN HDBaseT 4K RS232 AUDIO Tx Rx R L INPUT IR OUT IR IN HDBaseT AUDIO MIC IN AUDIO OUT RL MIX OUT RL Tx Rx Receiver Projector Speaker Matrix PT-HDBT-701-TXWP Laptop Blu-ray 1080P 70m 4K 40m HDMI: HDBaseT: RS232: Audio: VGA:

Button Control

SOURCE/AUTO Button
Press and hold the SOURCE/AUTO button for 3 seconds. When the button lights up green the PT-HDBT-701-TXWP is in AUTO mode. This mode automatically selects the last video source connected to the PT-HDBT-701-TXWP and outputs it to the display.
Press and hold again for approximately 3 seconds, the light will go out, and the device will be in Manual mode which will allow the user to momentarily press the button to toggle between the two sources.

1. where the HDBaseT Receiver/ Matrix Switcher will be located (somewhere near the display device). See the installation instructions for the 70M HDBaseT Receiver.
2. If using the Control Panel, run another twisted pair cable from the PT-HDBT-701-TXWP location to the location that the Control Panel will be mounted.
3. All Cat5e/6/7 cables should be terminated with jacks. This allows the permanent link between the two devices to be tested.
4. Use the appropriate category rated patch cable to connect the HDBaseT link to the HDBT OUT connector.
5. If using the Control Panel, use the supplied adapter cable to connect with the second cable and follow the installation instructions for the HDBaseT Receiver and Control Panel.

Note: We recommends Cat5e/6/7 cabling with alien crosstalk prevention technology for the performance of HDBaseT link.

4. Button Control

SOURCE/AUTO Button

Press and hold the SOURCE/AUTO button for 3 seconds. When the button lights up green the PT-HDBT-701-TXWP is in AUTO mode. This mode automatically selects the last video source connected to the PT-HDBT-701-TXWP and outputs it to the display. Press and hold again for approximately 3 seconds, the light will go out, and the device will be in Manual mode which will allow the user to momentarily press the button to toggle between the two sources.

RS232 Connection

There are two RS232 control modes switching via sending 50779% or 50780%.

1. Control this PT-HDBT-701-TXWP and far-end third-party device (such as Projector) device by the local PC, and the connection diagram shown as below:

[Diagram not included in extracted text]

1. Control the PT-HDBT-701-TXWP by the remote PC which is connected with Receiver. The RS232 control mode can be chosen via RS232 commands, please refer to the 5.3.1 Control Mode Switching for more details.

[Diagram not included in extracted text]

RS232 Control Software

Here take the software docklight as an example.

Installation

Please download the latest Software Version from the link below:
https://docklight.de/download/Docklight.zip
Then follow the installation wizard for installation on Windows 7 and 10.

After the installation, Docklight can be run for the first time and should look like the below screen shot:
Registration is not necessary unless you wish to save settings on exit, so unless you wish to register click on "OK" to close the window.

The next pop-up window can also be closed with "Continue". An empty project is enough to send and receive commands easily (The default setting is always “Start with a blank project / blank script “)
Click “OK” to close this window.

Now you are in the main view, where commands are sent and feedback is received.
The next step is to select the correct COM port of the PC. To do this, double-click on "COM1" in the corresponding setup window.
Click “Continue” to close this window.

In the following window, select the drop-down menu labeled "Send / Receive on Comm Channel", select the appropriate COM port and then click on "OK" at the bottom right corner.
All other settings can be left at default for most applications, but refer to device RS232 settings to be sure.
Double click on “COM1” to change to the right COM port.

In order to be able to send commands, open communication with the device by clicking on "Play". (1)
Then the keyboard function must be activated, so that commands can be written in the "communication window". (2)
Finally enter the command, for example "50701%". This is then confirmed by pressing "Enter" to send. Any response from the connected device will appear in red. (3)
Select the right COM port.

RS232 Command

Communication protocol: RS232 Communication Protocol
Baud rate: 9600 Data bit: 8 Stop bit: 1 Parity bit: none

Control Mode Switching

Signal Switching

VGA Scaling Configuration

The default output resolution for VGA is 1920x1080. Below is a list of the output resolutions the built-in scaler can output.

HDCP Compliance

VGA Image Adjustment

EDID Configuration

Note: EDID commands are for HDMI sources only.

Device Configuration

Input & Output

Control Parts

General

Panel Drawing

• 151.00 mm
• 80.00 mm
• 48.80 mm
• 108.60 mm
• 41.10 mm
• 70.00 mm
• 60.00 mm
• 4- 4.5 8x90°
• 2-M3 3- 3.5

Troubleshooting & Maintenance

Note: If your problem persists after following the above troubleshooting steps, seek further help from authorized dealer or our technical support.

After-Sales Service

If there appear some problems when running the product, please check and deal with the problems referring to this user manual. Any transport costs are borne by the users during the warranty.

1. Product Limited Warranty: The product will be free from defects in materials and workmanship for two years (The purchase invoice shall prevail). Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the unit is within the Warranty period must be presented to obtain warranty service.
2. What the warranty does not cover (servicing available for a fee):
3. Technical Support: For any questions or problems, contact your distributor or reseller and tell them the respective product name and version, the detailed failure situation as well as the formation of the cases.

• Warranty expiration.
• Factory applied serial number has been altered or removed from the product.
• Damage, deterioration or malfunction caused by:
• Normal wear and tear.
• Use of supplies or parts not meeting our specifications.
• No certificate or invoice as the proof of warranty.
• The product model showed on the warranty card does not match with the model of the product for repairing or had been altered.
• Damage caused by force majeure.
• Servicing not authorized by distributor.
• Any other causes which does not relate to a product defect.
• Delivery, installation or labor charges for installation or setup of the product.

Asking for Assistance

Technical Support:
Phone: +49 5971 800299 - 0
Fax: +49 5971 800299 - 99

Technical Support Hours:
8:30 AM to 5:00 PM Monday thru Thursday
8:30 AM to 4:00 PM Friday

Write to:
PureLink GmbH
Von-Liebig-Straße 10
D - 48432 Rheine
www.purelink.de
info@purelink.de

Legal & Compliance

Product identification

Model: PT-HDBT-701-TXWP – manual version 1.0

Trademarks and disclaimer

Product model and logo are trademarks. All other company and product names mentioned are trademarks of their respective owners. All rights reserved. No part of this publication may be copied or reproduced without prior written permission. We reserve the right to make changes to the device, packaging or manual and accept no liability for misprints.

EU conformity

PureLink hereby declares that this product PureTools PT-HDBT-701-TXWP complies with Directives 1907/2006/EU und 2011/65/EU. PureLink GmbH hereby declares that this product PureTools PT-HDBT-701-TXWP complies with Directives 2014/30/EU and 2014/35/EU.

The full text of the EU Declaration of Conformity is available at: http://www.purelink.de/ce/4251364706794_CE.pdf

FCC

Statement This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. It has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation.

Disposal of electrical and electronic equipment

WEEE reg. no.: DE 93847290

The crossed-out wheelie bin symbol on the product, packaging or in this manual means that electrical and electronic equipment must not be disposed of with household waste at the end of its life. Hand in old devices free of charge at a public collection point or return them to a distributor obliged to take them back. Remove batteries and lamps that can be removed without destroying the device before handing it in, and delete any personal data stored on the device. Details are regulated by national law. By returning old devices you help protect the environment.

Packaging

Dispose of packaging separately by material (paper/cardboard, plastics) via the local collection systems. Keep packaging material away from children – risk of suffocation. Packaging register LUCID: DE5958616449295.