CAUTION

Read the entire instruction manual before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, please contact your local distributor for assistance.

• Use with products heavier than the rated weights indicated may result in instability causing possible injury.
• Please closely follow the assembly instructions. Improper installation may result in damage or serious personal injury.
• Safety gear and proper tools must be used. This product should only be installed by professionals.
• Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
• Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
• This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

Required for Installation

Component Checklist

• upper column (x2)
• D
• front cover (x1)
• G
• mounting plate (x1)
• H
• rear cover (x1)
• I
• VESA extension adapter arm (x2)
• J

• M6x12 (x16)
• O
• cable clip holder (x5)
• R

Note: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, contact your place of purchase for a replacement.

Package M

• M8x50 (x4)
• M-E
• big spacer (x8)
• M-H

1. Installing the Wheel Casters

• B
• A
• U

2. Attaching the Columns to the Base

Align the column as shown, making sure that the cable management holes and the shorter legs on the same side.

• C
• M
• W

Note: Do not fully tighten the screws M.

3. Installing the Columns

• F

4. Installing the Shelf Mounting Brackets

Position the cable management holes (found on each upper column leg) facing inward as shown.

• D
• N
• Y

5. Installing the Front Cover and Equipment Shelf

• Position G as indicated, make sure the front of G and the longer legs on the same side.

• Make sure E and the shorter legs on the same side.

Caution: Fully tighten the screws M under the base.

6a. Attaching the Mounting Plate to the Display

VESA 200×200mm/300×300mm/350×350mm/400×200mm/400×400mm

Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screen.

6b-1. Installing the VESA Extension Adapter Arms

VESA 600x200mm

VESA 600x400mm

6b-2. Attaching the Mounting Plate to the Display

M-A | M-B | M-C | M-D | M-E | M-F | M-G | M-H

7. Mounting the Display onto the Screws / 8. Adjusting the Tilting Angle of the Display

Default Position (0°) | Tilted Position (5°)

9. Snuggly Adjusting the Rear Bolts / 10. Fixing the Display in Landscape/Portrait Position(If Necessary)

Tighten the screw to fix the screen.

11a: Routing the Cable / 11b-1: Attaching the Cable Clip Holders / 11b-2: Routing the Cable through Cable Clips

12. Attaching the Cable Covers

2a 2b

2c

13. Attaching the Rear Cover

• It is recommended to adjust the columns to the desired height before installing the display.
• If you want to adjust the columns height after finishing the display installation, Please remove the equipment shelf, then adjust the columns to the desired height.

Maintenance

• Check that the cart is secure and safe to use at regular intervals (at least every three months).

• Please contact your distributor if you have any questions.

Legal & Compliance

Product identification

Model: PM-CART-80W – manual version 1.0

Warranty and liability

The manufacturer grants the full statutory warranty on all new devices. As the manufacturer has no influence on installation, the warranty only applies to the product itself. If you detect a fault or damage, please contact your dealer and provide your sales slip or invoice as proof of purchase.

The manufacturer is not liable for damage to persons or property caused by improper installation, operation or maintenance not described in this manual. Do not alter or modify the product or its accessories. Any use other than described in this manual is not permitted and voids warranty and guarantee.

Trademarks and disclaimer

Product model and logo are trademarks. All other company and product names mentioned are trademarks of their respective owners. All rights reserved. No part of this publication may be copied or reproduced without prior written permission. We reserve the right to make changes to the device, packaging or manual and accept no liability for misprints.

Packaging

Dispose of packaging separately by material (paper/cardboard, plastics) via the local collection systems. Keep packaging material away from children – risk of suffocation. Packaging register LUCID: DE5958616449295.