Safety Precautions

• Unpack the equipment carefully and save the original box and packing material for possible future shipment
• Follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
• Do not dismantle the housing or modify the module. It may result in electrical shock or burn.
• Using supplies or parts not meeting the products’ specifications may cause damage, deterioration or malfunction.
• Refer all servicing to qualified service personnel.
• To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
• Do not put any heavy items on the extension cable in case of protrusion.
• Do not remove the housing of the device as opening or removing the housing may expose you to dangerous voltage or other hazards.
• Install the device in a place with sufficient ventilation to avoid damage caused by overheat.
• Keep the module away from liquids.
• Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on to the housing, unplug the module immediately.
• Do not twist or pull by force ends of the optical cable. It can cause malfunction.
• Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
• Unplug the power cord when left unused for a long period of time.
• Information on disposal for scrapped devices: do not burn or mix with general household waste, please treat them as normal electrical wastes.

Product Introduction

Thanks for choosing the PT-PMS-42S 4x2 multi-format seamless presentation matrix switcher with one PT-HDBT-210-RX receiver! The matrix switcher simplifies meeting room and presentation space system integration by providing three HDMI inputs, one USB-C input, one HDMI output and one HDBaseT output with one HDMI loop output. It also provides external one audio input to be embedded in the first HDMI input. Moreover, it provides one MIX audio input and one MIC audio input for global audio.
The matrix switcher provides true 4K scaling up to 4K@60Hz@4:4:4. Both inputs and outputs are capable of providing 4K@60Hz@4:4:4 signals. The HDBaseT output provides an innovative solution allowing transmission of HDMI 2.0 signals over a CATx cable while ensuring very high, original image quality. It is designed for use with the PT-HDBT-210-RX receiver. The USB-C input is ideal for AV interfacing with newer MacBook, Chromebook, and Windows PC, as well as smart phones and tablets.
The matrix switcher supports auto switching on HDMI, HDBaseT with HDMI loop outputs based on TMDS activity signals sensing. It also allows users to control system functionality via Web GUI, RS232, IR and CEC.
The matrix switcher is designed to be the central component of AV system. It is ideal for applications where multiple signals with different resolutions must be optimized for displays. It is also suitable for presentation spaces where two displays are needed.

Features

• 4x2 HDMI 2.0 seamless presentation switcher with matrix outputs.
• HDMI 2.0 and HDCP 2.2 compliant. The video resolution supports up to 4K@60Hz 4:4:4.
• Supports video resolution down-scaling and up-scaling, 1080P, 1920x1200P, 4K@30Hz, 4K@60Hz can be selected for HDMI and HDBaseT outputs.
• Supports auto switching.
• Features a mirrored HDMI output for HDBaseT output.
• Visually lossless video de-compression and compression for HDMI signals transmission up to 40m at 4K and 70m at 1080P on HDBaseT output.
• HDBaseT output support 24V PoC.
• One external L+R balanced audio input can be embedded in the first HDMI input.
• One MIX input and one MIC input for audio mixing.
• One L+R balanced audio output and one digital SPDIF audio output for audio de-embedding.
• MIX, MIC and output audio volume control.
• Supports ARC.
• Independent audio adjustment.
• Smart EDID management.
• Controllable via front panel buttons, RS232 local and pass-through, IR local and pass-through, TCP/IP, CEC and on OSD.

Package List

Matrix Switcher

• 1x PT-PMS-42S 4x2 HDMI 2.0 Seamless Matrix Switcher
• 2x Mounting Ears with 6 Screws
• 4x Plastic Cushions
• 1x IR Remote
• 1x IR Receiver (for IR EYE)
• 1x 3-pin Terminal Block
• 3x 5-pin Terminal Blocks
• 1x Power Adaptor (24V DC 2.71A)

HDBaseT Receiver

• 1x PT-HDBT-210-RX HDBaseT Receiver
• 2x Mounting Ears with 4 Screws
• 4x Plastic Cushions
• 1x 3-pin Terminal Block
• 1x User Manual

Note: Please contact your distributor immediately if any damage or defect in the components is found.

Matrix Switcher

HDBaseT Receiver

Matrix Switcher Front Panel

• ① Power LED: The LED illuminates red when the device is powered on.
• ② SOURCE: Total five buttons with blue backlight. 1. HDMI input selector / Left Key for On Screen Display control (OSD). 2. HDMI input selector / Right Key for OSD. 3. HDMI input selector / Up Key for OSD. 4. USB-C input selector / Down Key for OSD. Auto switching mode selector. Press this to enter or exit auto switching mode. / Press and hold it at least 2 seconds to enable OSD menu.
• ③ OUTPUTS: Two buttons with blue backlight. 1. HDMI output selector. 2. HDBT output selector.
• ④ RESOLUTION: Two output video resolution selectors. Press the 1. HDMI or 2. HDBT button repeatedly to cycle through the four video resolutions. A series of four LEDs, one of which illuminates blue to indicate which resolution is selected.
• ⑤ VOLUME: Press the volume knob in to toggle among MIX, MIC and AUDIO OUT audio control, and the corresponding LED will illuminate blue. Rotate the knob to increase or decrease the volume of the selected audio. Press and hold the knob at least three seconds to mute the selected audio. Rotate the knob to unmute.

Matrix Switcher Rear Panel

• ① INPUTS: Total four video inputs and one audio input. 1. HDMI: Type-A female HDMI port to connect the HDMI source. One external balanced audio input (5-pin) can be embedded in the HDMI input. 2. HDMI: Type-A female HDMI port to connect the HDMI source. 3. HDMI: Type-A female HDMI port to connect the HDMI source. 4. USB-C: Type-C USB port to connect the device with SlimPort output, e.g. MacBook.
• ② OUTPUTS: 1. HDMI: Type-A female HDMI port to connect the display device. 2. HDBT: RJ45 port to connect the PT-HDBT-210-RX receiver to transmit AV signal, IR and RS232 control signal. The HDBT output supports 24V PoC. 2. HDMI: Type-A female HDMI loop output port to connect the display device. Note: The 2. HDMI and 2. HDBT ports output the same signal. SPDIF: Toslink connector to connect speaker or amplifier for HDMI OUT (default) or HDBT OUT audio de-embedding, or it is used for ARC audio output from PT-HDBT-210-RX receiver. AUDIO: 5-pin terminal block to connect speaker or amplifier for HDMI OUT (default) or HDBT OUT audio de-embedding.
• ③ AUDIO INPUTS: MIX: 5-pin terminal block to connect the audio source for global audio mixing. MIC: Microphone audio input for global audio mixing. Put the Phantom (48V) switch in ON position, the 3-pin terminal block to connect condenser microphone. Put the Phantom (48V) switch in OFF position, the 3-pin terminal block to connect dynamic microphone.

• ④ CONTROL: IR IN: 3.5mm jack to connect the IR receiver for IR pass-through. IR OUT: 3.5mm jack to connect the IR emitter for IR pass-through. IR EYE: 3.5mm jack to connect IR receiver to control the switcher by the IR remote. FIRMWARE: Type-A USB port for firmware upgrade. RS232: 3-pin terminal block to connect the control device (e.g. PC) to control the switcher by sending RS232 commands. It also supports RS232 pass-through control. TCP/IP: RJ45 port to connect the control device (e.g. PC) to control the switcher by GUI.
• ⑤ DC 24V: DC connector for the power adapter connection.

Receiver Front and Rear Panel

• ① Power LED: The LED illuminates red when power is applied.
• ② ARC Mode: Press the button with paper clip or other sharp tool to enable the ARC mode, and then the left LED illuminates blue. Press it again to exit the ARC mode and the LED is off. The ARC mode also be enabled/disabled by sending RS232 command.
• ③ ARC Audio In: Toslink connector to connect ARC audio source device (e.g. TV).
• ④ FW: Micro-USB port for firmware upgrade.
• ⑤ HDMI Out: Type-A female HDMI output port to connect HDMI display (e.g. TV).
• ⑥ Audio Breakout: If the ARC mode is OFF, the Toslink connector is connected to speaker or amplifier for HDMI source audio de-embedding. Note that if the ARC mode is ON, this port has no audio output.
• ⑦ IR In: 3.5mm jack to connect the IR receiver for IR pass-through.
• ⑧ IR Out: 3.5mm jack to connect the IR emitter for IR pass-through.
• ⑨ RS232: 3-pin terminal block to connect the RS232 control device (e.g. PC) or a third-party device to be controlled.
• ⑩ HDBT In: RJ45 port to connect the HDBT output port of switcher/transmitter by CATx Ethernet cable. The LINK LED illuminates orange when there is a valid HDBaseT link between the switcher/transmitter and the receiver. The HDCP LED illuminates green when the video contains HDCP content.
• ⑪ DC 24V: DC connector for the power adapter connection. If the switcher/transmitter is connected to the power adaptor, the receiver doesn’t need to connect power adaptor due to the HDBT output port of switcher/transmitter supports 24V PoC output.

Usage Precaution

• Make sure all components and accessories included before installation.
• System should be installed in a clean environment with proper temperature and

humidity.

• All of the power switches, plugs, sockets, and power cords should be insulated and safe.

• All devices should be connected before power on.

System Diagram

The following diagram illustrates the typical input and output connection of the switcher:

RS232 Connection

The switcher supports RS232 local control and RS232 pass-through, and the receiver supports RS232 pass-through. There are five modes of RS232 control connection as below:

1. Connect PC to the RS232 port of switcher to control the switcher by sending RS232 commands. Please refer to the chapter 8.RS232 Control for more details.
2. Connect PC to the RS232 port of receiver to control the switcher by sending RS232 commands.
3. Connect PC to the RS232 port of switcher to control the far-end third-party device (e.g. Projector) which is connected to the RS232 port of receiver by sending RS232 commands.
4. Connect PC to the RS232 port of receiver to control the local third-party device which is connected to the RS232 port of switcher by sending RS232 commands.
5. Connect a third-party device to the RS232 port of switcher, the third-party device can be controlled by sending RS232 commands via the RS232 Control tab of GUI. Please refer to the chapter 7.7 RS232 Control Tab for more details.

IR Connection

The switcher provides IR EYE port for switcher control, and provides IR IN and IR OUT ports to be used together with the IR In and IR Out ports of receiver for source or display device control.

1. Connect the IR receiver to the IR EYE port of switcher to control the switcher by the IR remote.
2. Control the far-end display device: Connect the IR receiver to the IR IN port of switcher, and then connect the IR emitter to the IR Out port of receiver. The display device which is connected to the receiver can be control by its IR remote from the local switcher position.
3. Control the local source device: Connect the IR receiver to the IR In port of receiver, and then connect the IR emitter to the IR OUT port of switcher. The source device which is connected to the switcher can be control by its IR remote from the far-end receiver position.

Manual Switching

When the switcher is in manual switching mode, the AUTO button LED goes out. Please follow the below steps to switch input source to output channel.

1. Press any one of four input buttons to select input source, and the corresponding button LED turns blue.
2. Press either 1.HDMI or 2.HDBT output button to select output channel, and the corresponding button LED turns blue.
3. Press the input button again to confirm switching setting, otherwise, it will automatically confirm after three seconds.

Auto Switching

Please follow the below steps to enable auto switching mode for 1.HDMI or 2.HDBT output.

1. Press AUTO, and the button LED turns blue.
2. Press either 1.HDMI or 2.HDBT output button, and the corresponding button LED turns blue.
3. Press AUTO button again to confirm the setting, otherwise, it will automatically confirm after three seconds.
4. Repeat the above three steps can exit auto mode, but the input source will remain the current setting.

Note: The AUTO button LED illuminates blue when the 1.HDMI output is in auto mode or the 2.HDBT output in auto mode.

• The switcher will switch to the first available active input starting at input 1 to 4.
• New input: The switcher will automatically select the new input once detecting a new input.
• Reboot: If power is restored to the switcher, it will automatically reconnect the input before powered off.
• Source removed: When an active source is removed, the switcher will switch to the first available active input starting at 1.HDMI input.
• In auto mode, the input source also can be switched by the manual switching steps.

Switching Status Query

• Press any input button can get its corresponding output channel.
• Press any output button can get its corresponding input channel.

Example: 2.HDMI input is switched to the HDMI OUT.
Press 2.HDMI input button, and then the 2.HDMI source button and the 1.HDMI output button illuminate blue and last for 3 seconds.
Press 1.HDMI output button, and then the 2.HDMI source button illuminates blue and last for 3 seconds.

Resolution Selection

Press the 1.HDMI or 2.HDBT button on RESOLUTION area repeatedly to cycle through the four video resolutions. A series of four LEDs, one of which illuminates blue to indicate which resolution is selected.

Sound Volume Control

Press volume knob to choose MIX, MIC or AUDIO OUT audio needs to be adjusted, the corresponding LED will turn blue and keep on.

• Adjusting the knob in clockwise direction to increase sound volume.
• Adjusting the knob in anti-clockwise direction to decrease sound volume.
• Press and hold the knob at least three seconds to mute the selected audio. Rotate the knob to unmute.

IR Remote Control

Connect IR receiver to the IR EYE port, the switcher can be controlled by the following IR remote.

• Select input source
• Press AUTO to enable auto switching mode, and then select output channel.
• Select output channel
• Press BLACK, and then select output channel to make it output black screen.
• Enable/Disable OSD menu.
• Confirm and Navigation buttons: OK, UP, DOWN, LEFT and RIGHT for OSD menu.
• Return to the previous OSD menu.
• MIX input audio control: Mute, Volume Down and Volume Up.
• HDMI output audio control: Mute, Volume Down and Volume Up.
• HDBT output audio control: Mute, Volume Down and Volume Up.

4. USB-C
OK
2. HDBT BLACK
# 1
# 3
# 5
# 8
# 10
# 2
# 4
# 6
# 7
# 9

GUI Control

The switcher can be controlled via TCP/IP. The default IP settings are:

Type 192.168.0.178 in the internet browser, it will enter the below log-in webpage:
Username: admin
Password: admin
Type the user name and password, and then click Login to enter the section for video switching.

Video Switching Tab

• HDMI OUTPUT: Switch the selected input source to HDMI output. Click AUTO to enable/disable auto switching mode.
• HDBT OUTPUT: Switch the selected input source to HDBT output. Click AUTO to enable/disable auto switching mode.
• Preset: Save the current routing status to preset 1~6, or recall the previously saved preset.

Resolution Selection Tab

• HDMI OUTPUT: Select the HDMI output video resolution.
• HDBT OUTPUT: Select the HDBT output video resolution.

Audio Control Tab

Audio Input

• HDMI IN: Source: Select the HDMI audio stream of source device for 1.HDMI input. Embedded: Select the external balanced audio (5-pin) to be embed in 1.HDMI input.
• MIX: MIX input audio volume control (Volume Down, Volume Up, Mute/unmute).
• MIC: MIC input audio volume control (Volume Down, Volume Up, Mute/unmute).

Audio Output

• HDMI Output: Select MIX or MIC input audio to mix with the HDMI output audio, and then control the global output audio by volume bar and buttons.
• HDBT Output: Select MIX or MIC input audio to mix with the HDBT output audio, and then control the global output audio by volume bar and buttons.
• SPDIF Output: Select the audio source for the SPDIF output.
• RX ARC: Select the ARC audio from the PT-HDBT-210-RX, and the ARC audio volume cannot be adjusted.
• HDMI OUT: Select HDMI OUT audio to be de-embedded by the SPDIF output port. The SPDIF output audio volume will automatically follow the volume of HDMI output audio. When adjusting the HDMI output audio volume, the volume bar of SPDIF output audio will automatically be changed.
• HDBT OUT: Select HDBT OUT audio to be de-embedded by the SPDIF output port. The SPDIF output audio volume will automatically follow the volume of HDBT output audio. When adjusting the HDBT output audio volume, the volume bar of SPDIF output audio will automatically be changed.
• L+R Output: Select HDMI OUT or HDBT OUT audio to be de-embedded by the L+R audio output port.

Configuration Tab

PoC Setting

• Turn on or off PoC for HDBT output port.

EDID Management

• Select the compatible built-in EDID for the selected input source.
• Upload user-defined EDID by the below steps:

1. Prepare the EDID file (.bin) on the control PC.
2. Select the User-defined.
3. Click the box, and then select the EDID file (.bin) according the tooltip.
4. Click Confirm to upload the user-defined EDID.

EDID Management

• Select the compatible built-in EDID for the selected input source.
• Upload user-defined EDID by the below steps:

1. Prepare the EDID file (.bin) on the control PC.
2. Select the User-defined.
3. Click the box , and then select the EDID file (.bin) according the tooltip.
4. Click Confirm to upload the user-defined EDID.

CEC Control Tab

If the input source devices and display devices support CEC, they can be controlled by the below control buttons to replace IR remote.

1. Source Control: Select the input source which needs to be controlled, and then press function buttons.

1. Display Control: Select the output display which needs to be controlled, and then press function buttons.

User-defined

The switcher also provides user-define CEC functions, the CEC command can be edited and saved in the Trigger box.

• Select the input source, and then type CEC command in the Trigger 1 or Trigger 2 box to control the selected source.
• Select the output display, and then type CEC command in the Trigger 1 or Trigger 2 box to control the selected display.

Tags Setting Tab

• INPUTS: Modify the label of input sources.
• Preset: Modify the label of presets.

RS232 Control Tab

• Select Local or HDBT Out control mode.
• Local: Send RS232 commands to control the local third-party which is connected to the RS232 port of the switcher.
• HDBT Out: Send RS232 commands to control the far-end third-party (e.g. Projector) which is connected to the RS232 port of HDBaseT receiver.
• Select HEX or ASCII format.
• Baud Rate: Supports 2400, 4800, 9600, 19200, 38400, 57600 or 115200.
• Command Ending: NULL, CR, LF or CR+LF can be chosen.
• Command: Type command in this textbox to be sent.
• Trigger On: Type Power On command in this textbox to turn on the third-party device.
• Trigger Off: Type Power Off command in this textbox to turn off the third-party device.

Network Setting Tab

• Static IP or Dynamic Host Configuration Protocol (DHCP).
• Modify the static IP Address, Subnet Mask, and Gateway.

Security Setting Tab

• Modify the login password.
• Lock or unlock the front panel buttons.

GUI Upgrade

Please visit at http://192.168.0.178:100 for GUI online upgrade. Type the username and password (the same as the GUI log-in setting, modified password will be available only after rebooting) to login the configuration interface. After that, click Administration in the source menu to get to Upload Firmware as shown below:

Select the desired update file and press Apply, it will start upgrading then.

RS232 Control Software

Connect the RS232 port to control device (e.g. PC) with RS232 cable. The switcher can be controlled by sending RS232 commands.

Here take the software Docklight as an example.

• Installation
• Please download the latest Software Version from the link below: https://docklight.de/download/Docklight.zip
• Then follow the installation wizard for installation on Windows 7 and 10.
• After the installation, Docklight can be run for the first time and should look like the below screen shot:
• Registration is not necessary unless you wish to save settings on exit, so unless you wish to register click on "OK" to close the window.

The next pop-up window can also be closed with "Continue". An empty project is enough to send and receive commands easily (The default setting is always “Start with a blank project / blank script“)
Click “Continue” to close this window.
Click “OK” to close this window.

Now you are in the main view, where commands are sent and feedback is received. The next step is to select the correct COM port of the PC. To do this, double-click on "COM1" in the corresponding setup window.
In the following window, select the drop-down menu labeled "Send / Receive on Comm Channel", select the appropriate COM port and then click on "OK" at the bottom right corner.
All other settings can be left at default for most applications, but refer to device RS232 settings to be sure.

Double click on “COM1” to change to the right COM port.

In order to be able to send commands, open communication with the device by clicking on "Play". (1)
Then the keyboard function must be activated, so that commands can be written in the "communication window". (2)
Finally enter the command, for example "50701%". This is then confirmed by pressing "Enter" to send. Any response from the connected device will appear in red. (3)

Select the right COM port.

RS232 Command

Communication protocol: RS232 Communication Protocol
Baud rate: 9600 Data bit: 8 Stop bit: 1 Parity bit: none

Note: All commands needs to be ended with “<CR><LF>”.
In the commands, “[”and “]” are symbols for easy reading and do not need to be typed in actual operation.
Type the command carefully, it is case-sensitive.

Click “Play” to open the communication.
Enable the keyboard type in function.
Command sending area.
Monitoring area, indicates if the command sent works.
1
2
3

System Control

Video Switching

Preset Setting

Audio Control

Output Resolution Setting

EDID Management

CEC Control

When CEC control is enabled, if the input source devices and display devices support CEC, they can be controlled by sending CEC commands to replace IR remote.

According to the below command format to send specific command to control input source or display devices.

#SEND_CECCMD [port]:[command]Send CEC command to the specified port

• The [port] represents the port number. The input ports are 01~03, and the output ports are 04~06.

• The “[command]” represents the specific command from the table below.

Control the input source

Control the output display

Third-party Device Control

The switcher supports RS232 pass-through control, the third-party device can be controlled by RS232 command, and the command format as shown below:

• [PARAM1]=A/H: Represents the command format.

• [PARAM2]=01~02: Represents the RS232 port.

• [PARAM3]=01~07: Represents the baud rate of third-party device.

• XXXX: ASCII or HEX characters.

#SEND_A_01_05:123456789Explanation: Send the ASCII command “123456789” to the third-party device which is connected to the RS232 port of switcher. The baud rate of third-party device is 38400.

#SEND_H_02_05:30 31 32 33 34Explanation: Send the HEX command “30 31 32 33 34” to the third-party device which is connected to the RS232 port of receiver. The baud rate of third-party device is 38400.

• [PARAM1]=A/H: Represents the command format.

• [PARAM2]=01~02: Represents the RS232 port.

• [PARAM3]=01~07: Represents the baud rate of third-party device.

• XXXX: ASCII or HEX characters.

#SET_OF_A_01_03:123456789Explanation: Automatically send the ASCII command “123456789” to the third-party device which is connected to the RS232 port of switcher. The baud rate of third-party device is 9600.

#SET_OF_H_02_03:30 31 32 33 34Explanation: Automatically send the HEX command “30 31 32 33 34” to the third-party device which is connected to the RS232 port of receiver. The baud rate of third-party device is 9600.

• [PARAM1]=01~02: Represents the RS232 port.

• [PARAM2]=01~07: Represents the baud rate of third-party device.

• [PARAM1]=A/H: Represents the command format.

• [PARAM2]=01~02: Represents the RS232 port.

• [PARAM3]=01~07: Represents the baud rate of third-party device.

• XXXX: ASCII or HEX characters.

#SET_OF_A_01_03:123456789Explanation: Automatically send the ASCII command “123456789” to the third-party device which is connected to the RS232 port of switcher. The baud rate of third-party device is 9600.

#SET_OF_H_02_03:30 31 32 33 34Explanation: Automatically send the HEX command “30 31 32 33 34” to the third-party device which is connected to the RS232 port of receiver. The baud rate of third-party device is 9600.

• [PARAM1]=01~02: Represents the RS232 port.

• [PARAM2]=01~07: Represents the baud rate of third-party device.

OSD Control

The PT-PMS-42S provides a powerful OSD operation menu which contains 3 parts: optional settings, image settings, system settings etc.
There are two ways to enter OSD menu:

1. Press and hold the MENU/2s button at least two seconds on the front panel.
2. Press the MENU button on the IR remote.

Operation:

• Press direction buttons on IR Remote or on the front panel to switch between menu options and menu pages.
• Press OK on the IR Remote or ENTER button on the front panel to confirm the selection.

Options include Picture, Sound, Option, System, and Info.

PICTURE MENU

Note: When setting the Picture Mode to User, Picture Adjust and Colortemp Adjust are available.

SOUND MENU

OPTION MENU

SYSTEM MENU

INFO MENU

Firmware Upgrade

Please follow the steps as below to upgrade firmware by the FIRMWARE port on the rear panel:

1. Prepare the latest upgrade file (.bin) on PC.
2. Power off the switcher, and connect the FIRMWARE port of switcher to the PC with USB cable.
3. Power on the switcher, and then the PC will automatically detect a U-disk named of “BOOTDISK”.
4. Double-click to open the U-disk.
5. Directly copy the latest upgrade file (.bin) to the “BOOTDISK” U-disk.
6. Remove the USB cable after firmware upgrade.
7. After firmware upgrade, the switcher should be restored to factory default by sending command.

Panel Drawing

PT-PMS-42S Matrix Switcher

PT-HDBT-210-RX HDBaseT Receiver

DC 24V 1.HDMI 2.HDMI 3.HDMI 4.USB-C 1.HDMI
Phantom (48V)
ON OFF
MIC FIRMWARE RS232
Tx Rx
2.HDBT
L R
AUDIOSPDIF IR EYEIR IN IR OUT
OUTPUTS AUDIO INPUTS CONTROL
2.HDMI
L R
MIX
L R
AUDIO
1. HDMI 2. HDMI 3. HDMI
SOURCE OUTPUTS RESOLUTION VOLUME

PT-PMS-42S
Presentation Matrix
436.4 mm
44.0 mm
140 mm
19.5 mm
84 mm

Troubleshooting and Maintenance

Note: If your problem persists after following the above troubleshooting steps, seek further help from authorized dealer or our technical support.

After-Sales Service

If problems occur while operating the product, please use the troubleshooting and maintenance information in this manual to deal with these problems. Any transport costs are borne by the user during the warranty period.

1. Product Limited Warranty: The product will be free from defects in materials and workmanship for two years (purchase invoice date shall prevail). A proof of purchase is the evidence that the unit is within the warranty period. A bill of sale or receipted invoice must be presented to obtain warranty service.
2. What the warranty does not cover (servicing available for a fee): • Warranty has expired • The factory applied serial number has been altered or removed from the product. • Damage, deterioration or malfunction caused by: • Normal wear and tear. • Use of accessories, supplies or parts, not meeting our specifications. • No bill of delivery or invoice as proof of warranty. • The product model displayed on the warranty card does not match the product model for repairing or it has been altered. • Damage caused by force majeure. • Servicing, not authorized by distributor. • Any other cause not related to a product defect. • Delivery, installation or labor charges for product installation and/or product setup.
3. Technical Support: For any questions or problem troubleshooting inquiries, contact your distributor or reseller. Please provide the respective product name and version, a detailed description of the failure situation as well as how the failure occurred.

Legal & Compliance

Product identification

Model: PT-PMS-42S – manual version 1.0

Trademarks and disclaimer

Product model and logo are trademarks. All other company and product names mentioned are trademarks of their respective owners. All rights reserved. No part of this publication may be copied or reproduced without prior written permission. We reserve the right to make changes to the device, packaging or manual and accept no liability for misprints.

FCC

Statement This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. It has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation.

Disposal of electrical and electronic equipment

WEEE reg. no.: DE 93847290

The crossed-out wheelie bin symbol on the product, packaging or in this manual means that electrical and electronic equipment must not be disposed of with household waste at the end of its life. Hand in old devices free of charge at a public collection point or return them to a distributor obliged to take them back. Remove batteries and lamps that can be removed without destroying the device before handing it in, and delete any personal data stored on the device. Details are regulated by national law. By returning old devices you help protect the environment.

Batteries

Batteries must not be disposed of with household waste. Return used batteries free of charge to collection points or retailers.

Packaging

Dispose of packaging separately by material (paper/cardboard, plastics) via the local collection systems. Keep packaging material away from children – risk of suffocation. Packaging register LUCID: DE5958616449295.