2x1 4K Multiformat Presentation Switcher with Scaler – Control

Discontinued

PT-PSW-21

2x1 4K Multiformat Presentation Switcher with Scaler

The PureTools Scaler Switcher 2x1 is a presentation switcher with one HDMI and one VGA input, providing switching to a single HDBaseT output. It supports resolutions up to 4K UltraHD at 30Hz and can transmit AV signals …

ManualControl (TCP/IP)FAQSpecificationsDatasheetFirmwareCE

Available control interfaces. Expand an active type to see the full command table.

RS232 Commands28 commandsActive

ConnectionBaud rate: 9600 Data bit: 8 Stop bit: 1 Parity bit: none↓ CSV

Source: manual, chapter RS232 Control, page 17

Command	Description	Example	Response
SFUD	Software upgrading		Software Update
GET VER	Check the software version		Version Vx.x.x
FRST	Restore factory default		Factor Reset
WAKE	Wake up the system		Wake Up
SWIN H1	Switch to HDMI input		Switch to hdmi
SWIN VG	Switch to VGA input		Switch to vga
AUTO 01	Enable auto switching mode		Auto Switching
AUTO 00	Disable auto switching mode		Manual Switching
AUMT S1	Mute source audio		Audio Mute Source: Enable
AUMT S0	Unmute source audio		Audio Mute Source: Disable
VOLS AP	Increase the source volume to xx (xx=0~60)		Source Volume: xx
VOLS AN	Decrease the source volume to xx (xx=0~60)		Source Volume: xx
VOLS xx	Set the source volume to xx (xx=0~60)		Source Volume: xx
SRES 01	Change output resolution to 3840x2160		Resolution: 3840x2160
SRES 02	Change output resolution to 1920x1080		Resolution: 1920x1080
SRES 03	Change output resolution to 1280x720		Resolution: 1280x720
EDID DF	EDID default		EDID: Initial
EDID MN	Get the EDID data from display		EDID: Manage
EDID US	When the command applied, system prompts to upload the user-defined EDID file (.bin) from U-disk.		EDID: User
BAUD 115200	Set the RS232 baudrate to 115200		Set Baudrate 115200
BAUD 57600	Set the RS232 baudrate to 57600		Set Baudrate 57600
BAUD 38400	Set the RS232 baudrate to 38400		Set Baudrate 38400
BAUD 19200	Set the RS232 baudrate to 19200		Set Baudrate 19200
BAUD 9600	Set the RS232 baudrate to 9600		Set Baudrate 9600
BAUD 2400	Set the RS232 baudrate to 2400		Set Baudrate 2400
BAUD 4800	Set the RS232 baudrate to 4800		Set Baudrate 4800
/+b:xxxxxxxxx	Send ASCII command to control far-end third party device from the scaler switcher to receiver based on RS232 pass-through function. b \| Baud Rate 0 \| 2400 1 \| 4800 2 \| 9600 3 \| 19200 4 \| 38400 5 \| 57600 6 \| 115200 xxxxxxxxx is for ASCII data (max 48 Byte).	/+2:123456789 — Send the ASCII command “123456789” to control the third party device of which baud rate is 9600.
/-b:xx xx xx xx	Send HEX command to control far-end third party device from the scaler switcher to receiver based on RS232 pass-through function. b \| Baud Rate 0 \| 2400 1 \| 4800 2 \| 9600 3 \| 19200 4 \| 38400 5 \| 57600 6 \| 115200 xx xx xx xx is for HEX data (max 48 Byte).	/-2:30 31 32 33 34 — Send the HEX command “30 31 32 33 34” to control the third party device of which baud rate is 9600.